Vectorization and Loops

Interactions with Loop Parallelization

This topic provides more information on the interaction between the auto-vectorizer and loops.

Combine the [Q]parallel and [Q]x options to instruct the Intel® Fortran Compiler to attempt both Auto-Parallelization and automatic loop vectorization in the same compilation.

In most cases, the compiler will consider outermost loops for parallelization and innermost loops for vectorization. If deemed profitable, however, the compiler may even apply loop parallelization and vectorization to the same loop.

Types of Vectorized Loops

For integer loops, the 128-bit Intel® Streaming SIMD Extensions (Intel® SSE) and the Intel® Advanced Vector Extensions (Intel® AVX) provide SIMD instructions for most arithmetic and logical operators on 32-bit, 16-bit, and 8-bit integer data types, with limited support for the 64-bit integer data type.

Vectorization may proceed if the final precision of integer wrap-around arithmetic is preserved. A 32-bit shift-right operator, for instance, is not vectorized in 16-bit mode if the final stored value is a 16-bit integer. Also, note that because the Intel® SSE and the Intel® AVX instruction sets are not fully orthogonal (shifts on byte operands, for instance, are not supported), not all integer operations can actually be vectorized.

For loops that operate on 32-bit single-precision and 64-bit double-precision floating-point numbers, Intel® SSE provides SIMD instructions for the following arithmetic operators:

• addition (+)

• subtraction (-)

• multiplication (*)

• division (/)

Additionally, Intel® SSE provide SIMD instructions for the binary MIN and MAX and unary SQRT operators. SIMD versions of several other mathematical operators (like the trigonometric functions SIN, COS, and TAN) are supported in software in a vector mathematical run-time library that is provided with the Intel® Fortran C++ Compiler.

To be vectorizable, loops must be:

• Countable: The loop trip count must be known at entry to the loop at runtime, though it need not be known at compile time (that is, the trip count can be a variable but the variable must remain constant for the duration of the loop). This implies that exit from the loop must not be data-dependent.

• Innermost loop of a nest: The only exception is if an original outer loop is transformed into an inner loop as a result of some other prior optimization phase, such as unrolling, loop collapsing or interchange, or an original outermost loop is transformed to an innermost loop due to loop materialization.

• Without function calls: Even a print statement is sufficient to prevent a loop from getting vectorized. The vectorization report message is typically: non-standard loop is not a vectorization candidate. The two major exceptions are for intrinsic math functions and for functions that may be inlined.

Intrinsic math functions such as sin(), log(), fmax(), and so on, are allowed, because the compiler runtime library contains vectorized versions of these functions. See the table below for a list of these functions; most exist in both float and double versions.

The loop in the following example may be vectorized because sqrt() is vectorizable and func() gets inlined. Inlining is enabled at default optimization for functions in the same source file. An inlining report may be obtained by setting the options Qopt-report:2 Qopt-report-phase:ipo (Windows) or qopt-report=2 qopt-report-phase=ipo (Linux).

Statements in the Loop Body

The vectorizable operations are different for floating-point and integer data.

Integer Array Operations

The statements within the loop body may be arithmetic or logical operations (again, typically for arrays). Arithmetic operations are limited to such operations as addition, subtraction, ABS, MIN, and MAX. Logical operations include bitwise AND, OR, and XOR operators. You can mix data types but this may potentially cost you in terms of lowering efficiency.

Other Operations

No statements other than the preceding floating-point and integer operations are valid. The loop body cannot contain any function calls other than the ones described above.

Data Dependency

Data dependency relations represent the required ordering constraints on the operations in serial loops. Because vectorization rearranges the order in which operations are executed, any auto-vectorizer must have at its disposal some form of data dependency analysis.

An example where data dependencies prohibit vectorization is shown below. In this example, the value of each element of an array is dependent on the value of its neighbor that was computed in the previous iteration.

subroutine dep(data, n)
  real :: data(n)
  integer :: i
 do i = 1, n-1
    data(i) = data(i-1)*0.25 + data(i)*0.5 + data(i+1)*0.25
  end do 
end subroutine dep

The loop in the above example is not vectorizable because the WRITE to the current element DATA(I) is dependent on the use of the preceding element DATA(I-1), which has already been written to and changed in the previous iteration. To see this, look at the access patterns of the array for the first two iterations as shown below.

I=1: READ DATA(0) 
      READ DATA(1) 
      READ DATA(2) 
      WRITE DATA(1) 
I=2: READ DATA(1) 
      READ DATA(2) 
      READ DATA(3) 
      WRITE DATA(2)

In the normal sequential version of this loop, the value of DATA(1) read from during the second iteration was written to in the first iteration. For vectorization, it must be possible to do the iterations in parallel, without changing the semantics of the original loop.

  do i=1,100
   a(i)=b(i)
    end do
    
! which has the following access pattern
    read b(1)
    write a(1)
    read b(2)
    write b(2)

Data Dependency Analysis

Data dependency analysis involves finding the conditions under which two memory accesses may overlap. Given two references in a program, the conditions are defined by:

• whether the referenced variables may be aliases for the same (or overlapping) regions in memory.

• for array references, the relationship between the subscripts.

The data dependency analyzer for array references is organized as a series of tests, which progressively increase in power as well as in time and space costs.

First, a number of simple tests are performed in a dimension-by-dimension manner, since independency in any dimension will exclude any dependency relationship. Multidimensional arrays references that may cross their declared dimension boundaries can be converted to their linearized form before the tests are applied.

Some of the simple tests that can be used are the fast greatest common divisor (GCD) test and the extended bounds test. The GCD test proves independency if the GCD of the coefficients of loop indices cannot evenly divide the constant term. The extended bounds test checks for potential overlap of the extreme values in subscript expressions.

If all simple tests fail to prove independency, the compiler will eventually resort to a powerful hierarchical dependency solver that uses Fourier-Motzkin elimination to solve the data dependency problem in all dimensions.